АК «НЕНС»

АК «НЕНС»

Appointment: metal, machinery
Packing:
25 kg
10 kg
Color:
Цвет: RAL 9017. Black

This product is available tinting colors according to your desire. For details check with the Manager


!ATTENTION: Work only with LEGAL ENTITIES.

Price: 191.00 RUB/kg
The number:
Product successfully added!
To order, go to basket
Continue shopping

Description

Features

Application methods

Video (1)

Certificates (3)

Available colors RAL (106)

The ground-enamel acrylic "NANCE" is intended for painting metal surfaces, including transportation structures, rolling stock, agricultural equipment, requiring good decorative properties and long service life in the ambient conditions of up to minus 60oC and internal works. Has a high physical-mechanical and decorative features. Possesses high covering ability, ease of application. The ground-enamel forms a coating with a period of exploitation in conditions of the industrial atmosphere temperate-cold climate ( NF1) at least 5 years at a dried film thickness of 60-70 microns. . Coating primer-acrylic enamel AK "NANCE" has a high weather resistance, good adhesion to metal surfaces with different degrees of roughness, elasticity , resistance to shock, resistance to short-term exposure of industrial oil.

SHELF LIFE

The ground-enamel acrylic "NANCE" must be stored in a closed container in a dry place to prevent direct exposure to heat, sunlight and moisture at a temperature of from minus 300C to plus 400C.

Warranty period of storage primer enamel- 12 months from date of manufacture.

Заключение от РЖД - АК НЕНС

Наименование показателя

Норма

Цвет пленки эмали

Должен находиться в пределах допускаемых отклонений, установленных контрольными образцами цвета, картотекой цвета RAL

Внешний вид пленки

После высыхания пленка должна быть гладкой, однородной, без расслаивания, оспин, потеков, морщин и посторонних включений.

Условная вязкость (20,0±0,5)°С по вискозиметру ВЗ-246 с диаметром сопла 4мм, с, не менее

50

Массовая доля нелетучих веществ, %, не менее

45

Степень перетира, мкм, не более

35

Время высыхания покрытия до степени 3, ч,  при температуре (20,0±0,5)0 , ч, не более

3

Эластичность плёнки при изгибе, мм, не более

3

Прочность покрытия при ударе по прибору У-1, см, не менее

30

Твёрдость покрытия по маятниковому прибору, не менее:

типа ТМЛ, маятник А, отн.ед.

или

типа М-3, усл.ед.

 

 

0,2

 

0,25

Адгезия покрытия, баллы, не более

2

Укрывистость высушенного покрытия, г/м2, не менее

70

Блеск по блескомеру ФБ-2, %, не менее

25

Стойкость пленки при температуре (20±2)°С к статическому воздействию, ч, не менее

воды

трансформаторного масла

 

 

48

24

Заключение от РЖД - АК НЕНС

The painted surface must be cleaned from mechanical impurities, rust, scale степени2по to GOST standard 9.402-2004 or abrasive blast method to degree Sa 21/2 or mechanically to degree St 3 according to GOST R ISO 8501-1. The roughness of the cleaned surface( for ГОСТ2789) not more than 40 microns. Degreasing is toluene, xylene or solvents of grades P-4,R-5. Drying the surface after degreasing prior to application of the primer-enamel for 15-30 min.

Before applying the primer, thoroughly mix the enamel and, if necessary, diluted to the working viscosity by viscometer VZ-246 with nozzle diameter 4 mm at a temperature of 200C xylene , toluene . Recommended working viscosity during application depending on the application method:

brush or roller – 30-40 with .
pneumatic spraying is 25-27 C.
airless spray – 35-50 C.
Metal surfaces are painted with an ambient temperature of 5 to 350C and relative humidity above 80%.

Recommended coating thickness( dry layer) of 60-100 microns. Coating thickness( dry layer) in single layer application is 30-35 µm ( with paint spray) and 60-100 µm (by airless spray). The number of layers is determined individually depending on the application method. When painting in two layers, the interlaminar aging time of at least 15 min at 200C and at least 60 min at 50C. Final drying of the coating thickness up to 100 µm( dry layer) at 200C – at least 24 hours, at 50C - at least 48 hours. Installation and transportation of painted metal structures and parts no earlier than 72 hours after staining.

The theoretical flow rate of enamel for one-layer coating thickness ( dry layer) 30-35 µm is 60-100 g/m2 depending on the color. Actual consumption needs to take into account technological losses , depending on the application method, the degree of atomization, surface roughness, configuration of goods, etc.

Заключение от РЖД - АК НЕНС
RAL 1000
RAL 1001
RAL 1002
RAL 1003
RAL 1004
RAL 1005
RAL 1006
RAL 1007
RAL 1011
RAL 1013
RAL 1014
RAL 1015
RAL 1017
RAL 1018
RAL 1021
RAL 1023
RAL 1028
RAL 1032
RAL 1034
RAL 2001
RAL 2003
RAL 2004
RAL 2008
RAL 2010
RAL 2011
RAL 2012
RAL 3000
RAL 3001
RAL 3002
RAL 3003
RAL 3004
RAL 3005
RAL 3011
RAL 3012
RAL 3016
RAL 3020
RAL 3022
RAL 3028
RAL 5002
RAL 5003
RAL 5005
RAL 5007
RAL 5010
RAL 5012
RAL 5013
RAL 5015
RAL 5017
RAL 5018
RAL 5021
RAL 6001
RAL 6002
RAL 6004
RAL 6005
RAL 6010
RAL 6011
RAL 6016
RAL 6018
RAL 6019
RAL 6021
RAL 6024
RAL 6025
RAL 6026
RAL 6029
RAL 6032
RAL 6037
RAL 7000
RAL 7001
RAL 7004
RAL 7011
RAL 7012
RAL 7015
RAL 7016
RAL 7023
RAL 7032
RAL 7035
RAL 7036
RAL 7038
RAL 7040
RAL 7042
RAL 7043
RAL 7044
RAL 7045
RAL 7046
RAL 7047
RAL 8000
RAL 8002
RAL 8003
RAL 8004
RAL 8011
RAL 8012
RAL 8014
RAL 8015
RAL 8016
RAL 8017
RAL 8019
RAL 8022
RAL 8023
RAL 8028
RAL 9001
RAL 9002
RAL 9003
RAL 9004
RAL 9010
RAL 9011
RAL 9016
RAL 9018

Similar products:

Need help?
Professional help
If you have any difficulties, you can contact our specialists:

8 (800) 700-79-72
8 (800) 700-53-88
8 (835-33) 4-76-83

ICQ 281-034-662
ICQ 671-614-398
ICQ 656-767-981

X
X
X
Thanks for the request!
Your order,
expect a call specialist
Well