Emal UR-1012

Emal UR-1012

Appointment: tree, metal
Packing:
8 kg
20 kg
Color:
This product is available tinting colors according to your desire. For details check with the Manager


!ATTENTION: Work only with LEGAL ENTITIES.

Price: 302 RUB/kg.
The number:
Product successfully added!
To order, go to basket
Continue shopping

Description

Features

Application methods

Certificates (1)

Polyurethane enamel UR-1012 is designed for corrosion protection

internal surfaces of tanks, cisterns, storage under acetone, light (gasoline, kerosene, diesel fuel and heating oil) and dark (any type of fuel oil and distillate oil) the oil;
pumping and storage equipment, operated in an open industrial atmosphere temperate, cold, sea and tropical climates, and also in atmospheres containing corrosive agents.
Coating system consisting of polyurethane enamel, applied on primed surface, retains protective and decorative properties in an open industrial atmosphere of moderate and cold climate for 12 years, and in the atmosphere of the sea and tropical climate up to 5 years if the established technology is the application of rules of storage and transportation.

Polyurethane enamel UR-1012 available in different colors in accordance with RAL catalogue colors.

Заключение от РЖД - АК НЕНС

Наименование показателя

Норма

Внешний вид пленки

После высыхания пленка должна образовывать однородную глянцевую или полу-глянцевую поверхность

Условная вязкость при температуре (20,0±0,5)°С по вискозиметру ВЗ-246 с диаметром сопла 4 мм, с, не менее

60

Массовая доля нелетучих веществ, %, не менее

50

Степень перетира, мкм, не более

25

Время высыхания до степени 3 при температуре ( 20,0±0,5)0, ч, не более

3

Эластичность плёнки при изгибе, мм, не более

1

Прочность пленки при ударе на приборе У-1А, см, не менее

50

Твёрдость плёнки по маятниковому при-бору ТМЛ, не менее, отн.ед.

0,4

Адгезия пленки, баллы, не более

1

Стойкость пленки при температуре (20±2)°С к статическому воздействию, ч, не менее:

воды

трансформаторного масла

бензина

 

 

72

48

48

Заключение от РЖД - АК НЕНС

The painted surface must be cleaned from mechanical impurities, water-soluble salts, greases and oils. Degreasing is done with a rag soaked with solvent, xylene, acetone or other aromatic solvents.

The surface before painting must be dry and clean.

Before applying the semi-finished enamel mix it thoroughly and introduce the required amount of hardener, stirred, incubated for 15-20 min. If necessary, the enamel is diluted to working viscosity by viscometer VZ-246 with nozzle diameter 4 mm at a temperature (20,0±0,5)0C solvent R-5A (GOST 7827-74) or a mixture of xylene (GOST 9410-78, GOST or 9949-76) and butyl acetate (GOST 8981-78) in the ratio of 4:1. Recommended working viscosity for application by brush or roller – 35, a pneumatic spray – 8-22 with airless spray – 45 C.

The enamel is applied to the surface by means of pneumatic and airless spraying, brush or roller in 1-2 layers at an ambient temperature of 5 to 350C and relative humidity above 80%.

Заключение от РЖД - АК НЕНС

Similar products:

Need help?
Professional help
If you have any difficulties, you can contact our specialists:

8 (800) 700-79-72
8 (800) 700-53-88
8 (835-33) 4-76-83

ICQ 281-034-662
ICQ 671-614-398
ICQ 656-767-981

X
X
X
Thanks for the request!
Your order,
expect a call specialist
Well